TRAINING CATEGORIES
(Click Category to List Courses)

51 - LONG - Long-Term Programs


LONG 250A - Oil and Gas Production & Processing (26 Weeks)

Please contact us for fees

 

Course Description

This course will start by defining oil and production and processing, oil and gas properties, specifications and end uses. Then, typical oil and gas processing operations will be discussed, including oil and gas separation, oil desalting, oil degassing, oil movement, gas dehydration, acid gas removal, recovery of ethane, propane and NGL (natural gas liquids), liquefied natural gas (LNG) operations and oil refinery. Sulfur recovery will also be discussed. Typical equipment and facilities that are found in typical oil and natural gas processing operations will also be discussed including compressors, vessels, relief systems and safety system

Note: This course can be conducted only on the condition of having +5 participants. 

Course Objectives

  • Gaining knowledge of the properties, specifications and end uses of Oil &natural gas
  • Understanding the typical oil and natural gas processing operations
  • Gaining a deep understanding of the production of oil and gas 
  • Gaining knowledge of the different equipment and facilities found in oil and natural gas processing plants

Who Should Attend?

  • Petroleum engineers
  • Processing engineers
  • Operation engineers 
  • Commercial analysts
  • Decision makers/ investors in oil and gas sector

Course Details/Schedule

Part 1

  • Basic heat and heat transfer concepts
  • Draught and combustion
  • Feed Water- Properties of water and water treatment
  • Boiler and Auxiliaries
  • Boiler Types and Construction-feed system - Fitting
  • Mounting and Auxiliaries Equipment
  • Control and Instrumentation
  • Energy Efficiency
  • Operation. Step by Step Operation Procedures
  • Daily and Weekly Check and Logging
  • Actions in an Emergency
  • Testing and Maintenance
  • Fuel Concepts
  • Safety Aspects. Hazards of ( Steam- Flammable materialsand Flue Gases.)

Part 2

  • Utilities and Ancillaries Desalination plant
  • Introduction
  • Desalination plant
  • Construction instruments and control system
  • Unit start-up
  • Shut-down procedures
  • Multistage eject compression (MSEC)
  • Operation Process
  • Unit start and shut down 
  • Reverse osmosis system
  • Water Softening Plant
  • Troubleshooting

Part 3

  • Operation of Gas Turbines and Compressors
  • Gas Turbine cycles
  • Compressor-The Air Path
  • Combustion Section-Hot Air Path
  • The Turbine Section.
  • Turbine Auxiliaries & Starting Device
  • Generator
  • Excitation System
  • Electrical Distribution System
  • Start up & shut down using demonstration a simulator (Practical)
  • Introduction to compressors
  • Types of compressors
  • Centrifugal compressors
  • Piston compressors
  • Operation principle
  • Start up and shutdown procedures
  • Troubleshooting

Part 4

  • Heat transfer and Heat Exchangers
  • Introduction Heat Transfer
  • Methods of heat transfer
  • Factors affecting of Heat
  • Heat Exchangers media
  • Properties of thermal fluids
  • Lagging materials
  • Heat exchanger construction
  • Types of heat exchangers
  • Applications of heat exchangers
  • Operation of heat exchangers
  • Trouble shooting and safety aspects
  • Demonstration on a simulation (start up and shut down procedures

Part 5

  • Pumps and Compressors
  • Introduction to pumps & compressors
  • Types of Pumps & compressors
  • Centrifugal compressor- pumps
  • Piston compressor-pumps
  • Operating principles
  • Start up and shutdown
  • Demonstration on a simulation “start up and shut down- Trouble shooting" procedures

Part 6

  • Industrial Water Process
  • Chemistry of water
  • Types of raw water
  • Types of industrial water
  • Importance of water in process industry
  • Sources of water for process industry
  • Pre-treatment and treatment methods for process water
  • Physical and chemical properties of water
  • General laboratory analysis for process water

 

ETABS and SAFE. Training 24 CCE 210 5 SAP 2000. Training 25 CCE 305 5 Quality Assurance in Pavement Construction 26 CCE 401 5 Construction Project Management 27 CCE 402 10 Construction Project Management (10 Days) 28 CCE 403 5 Construction Project Management-Intensive 29 CCE 405 5 Principles of Construction Project Management 30 CCE 406 10 Principles of Construction Project Management (10 Days) 31 CCE 410 10 Construction Project and Risk Management (10 days) 32 CCE 411 5 Project & Contract Management for Marine Construction 33 CCE 412 5 Application of GIS in Construction Management 34 CCE 415 4 Sustainable Water Management Techniques, Innovation and Solution (4 Days) 35 CCE 419 5 Construction Management of Hydraulic Projects 36 CCE 420 5 Water Project Management 37 CCE 421 10 Modern Technologies in the Supervision and Quality Control of Irrigation Projects and Dealing with Contractors (10 Days) 38 CCE 422 5 Rapid Earthquake Hazard Evaluation of Buildings 39 CCE 425 10 Practical Application of Computers in Structural Engineering (10 Days) 40 CCE 428 5 Survey & Profile Using Total Station 41 CCE 430 5 Bridge Construction and Maintenance 42 CCE 435 5 Bridge Inspection and Maintenance 43 CCE-A 410 10 إدارة المشاريع الهندسية -10 أيام
21 - TTC - Transportation and Traffic Control
22 - ADV - Architectural Design and Visualization
23 - SRM - Safety and Occupational Health
24 - CSM - Public Relations, Communication Skills & Office Management
25 - TEM - Training and Education Management
26 - CMR - Customer Relations